They are making a number of great observations related to Tools You Need to Install a New Bathtub as a whole in the article followed below.
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is likewise a moderately tough job. If the old tub is readily available, the project can relocate rapidly; if you need to open a wall surface to get rid of the old bathtub as well as position the new tub, the job is much harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. See to it you have actually qualified yourself for the task and are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Chances are you might require an expert plumber to make tube links.
This article will certainly assist you mount a new bath tub in your bathroom if you have currently acquired a brand-new tub as well as don't need to alter the setup of your previous water system pipelines.
Your devices as well as product checklist need to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of removing the existing taps can be fairly problematic as a result of the limited access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will originate from the pipes. Once the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the tap in place with the maker given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be linked to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of the two wooden boards under its feet, put the tub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest flexible faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Fill the bathtub and additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub needs to wait until the bath tub has been made use of a minimum of once as this will resolve it into its final placement.
Getting ready for the Installation
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, bring about problems with wetness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealant can split fairly early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our article on Installing A Bathtub. Thanks a ton for taking time to read our piece. If you appreciated our post if you please make sure you remember to share it. I am grateful for your time. Come back soon.
Premium plumbing emergency care here.